Ford Ranger PX Parts Guide: Brakes, Tie Rod Ends, Centre Bearing & Service Parts

Basco DCB1021 driveshaft centre support bearing to suit Ford Ranger PX

The Ford Ranger PX is one of the most common utes in Australia, and plenty of PX1, PX2 and PX3 models are now well past their warranty and working hard. This guide covers five jobs that come up often: front brake pads, rear brake shoes, the outer tie rod ends, the tailshaft centre bearing, and the drive belt and oil filter service. For each one, it explains the signs, what you can check, and which parts we stock. Several also suit the Ford Everest and Mazda BT-50.

1. Front brake pads: squeals, shudder and pulling

A loaded or towing Ranger puts a lot of heat through its front brakes.

Signs:

  • A squeal or grinding when braking.
  • A shudder through the pedal or steering wheel, often from rotors with uneven thickness.
  • The ute pulling to one side under brakes.
  • A pedal that travels further than usual.

Check: look through the wheel at pad thickness and the rotor face. A lip at the rotor edge, deep grooves or blue heat marks mean the rotors need measuring.

2. Rear brake shoes: handbrake and stopping power

The PX uses drum brakes at the rear, and utes that tow or carry loads wear rear shoes faster.

Signs: a handbrake that needs more and more lever travel, a scraping noise from the rear, or the rear brakes feeling weak.

Check: at every service, have the drums removed and the shoe lining, drum diameter and wheel cylinders checked. Oil or brake fluid on the shoes means they must be replaced and the leak fixed.

  • Bendix BS5021 Rear Brake Shoe Set, $89.95: set of 4 shoes for the 294mm drum. Listed for the Ranger PX1, PX2, PX3 and PY and the BT-50 UP / UR, 4WD only. 2WD models typically use a different shoe, so confirm before ordering.

3. Outer tie rod ends: vague steering and edge tyre wear

The outer tie rod ends connect the steering rack to the hubs. When they wear, the steering loses its precision.

Signs: a knock over bumps or when turning, vague or wandering steering, or front tyres wearing on the inside or outside edge.

Check: with the front safely on stands, rock the wheel at 9 and 3 o'clock while someone watches the tie rod end. Any play in the joint, or a torn boot leaking grease, means it's due.

Count the turns when removing the old end so the new one goes on close to the original setting, and always get a wheel alignment straight after.

4. Tailshaft centre bearing: vibration and clunks

The centre bearing supports the middle of the two-piece tailshaft. Its rubber carrier ages and tears, especially on utes that tow.

Signs: a vibration through the floor at certain speeds, a rumble or squeal from under the middle of the ute, or a clunk when taking off.

Check: with the ute safely supported, look for a cracked or torn rubber carrier and try to move the shaft by hand near the bearing. Check the uni joints for play at the same time.

  • Basco DCB1021 Driveshaft Centre Support Bearing, $64.95: 35mm bearing with a heavy-duty rubber carrier, listed for the Ranger PX, PXII and PXIII and select BT-50 models. Confirm the bearing size and mounting centres against your old one.

5. Drive belt and oil filter: the service basics

Drive belt signs: squealing on start-up, cracks across the ribs, missing chunks or glazing. Check the tensioner and idler pulleys at the same time.

  • Gates 7PK3110 Micro-V Drive Belt, $83.95: listed for the Ranger PX, PXII and PXIII 3.2L and Everest UA 3.2L with A/C. Gates doesn't list it for the BT-50.
  • Ryco R2720P Premium Oil Filter, $29.95: cartridge filter for the Ranger PX and PY 2.0L Bi-Turbo, 2.2L and 3.2L diesel, the Everest and the BT-50 UP / UR diesel.

Follow the intervals in your logbook, and treat towing and dusty conditions as severe-duty use.

Replace now or keep an eye on it?

  • Replace brake pads and shoes at minimum thickness, or straight away if grinding or contaminated.
  • Replace a tie rod end with any play or a torn boot.
  • Replace the centre bearing if the rubber carrier is torn or you have driveline vibration.
  • Monitor a drive belt with fine surface cracks only, and recheck at the next service.

DIY difficulty and safety

  • Oil filter and drive belt: easy to moderate. Photograph the belt routing first.
  • Front pads: moderate. Measure the rotors, clean and lubricate the slide pins, and pump the pedal until firm before driving.
  • Rear shoes: moderate to hard. Drum brake springs and adjusters need care. Adjust the shoes and handbrake to the workshop manual setting.
  • Tie rod end: moderate. Needs a wheel alignment afterwards.
  • Centre bearing: moderate to hard. Mark the tailshaft before removal so it goes back in the same orientation, and the bearing needs pressing on.

Use stands on firm, level ground, never just a jack, and tighten everything to the torque in your workshop manual. Brakes, steering and the driveline are safety-critical. If you're unsure, have a qualified mechanic do the work.

FAQ

Will the BS5021 shoes fit my 2WD Ranger?
They're listed for 4WD models only. 2WD models typically use a different shoe. Send us your VIN and we'll check.

Do you stock the left-hand tie rod end?
We currently list the right-hand TE3252. Ask us about the left side.

Will the 7PK3110 belt fit a Ranger without air-con?
Non-A/C vehicles typically use a different length belt, so check the rib count and length.

Will non-genuine parts void my warranty?
Not on their own. The ACCC says you can use an independent mechanic and non-genuine parts, as long as the parts are fit for purpose and the work follows the manufacturer's schedule. Keep your receipts and logbook stamps.

See more in our braking and suspension and steering ranges.

Not sure which part fits your Ranger?

Check the fitment table on each product page, read our How to Check Fitment guide, or just ask us. Send your rego or VIN to sales@hoorooautomotiveparts.com.au or call the HOOROO Crew on (07) 5495 1839, and we'll confirm the right part before you order. Everything ships from our Sunshine Coast QLD warehouse, and spend $160 or more and shipping is free Australia-wide, applied automatically at checkout.

Find it. Fit it. Fair Dinkum™.
The HOOROO Crew

This article is general information only. Always have your vehicle inspected and repaired by a qualified mechanic.