Basco TE10000 Outer Tie Rod End - Front Left or Right Hand Side - to suit Holden Colorado RC (2008 - 2012), Isuzu D-Max TFR/TFS (2008 - On) & MU-X
Order before 1pm AEST (Mon–Fri) for same-day dispatch from the Sunshine Coast, QLD
Australia Post: 2–6 business days standard, 1–3 business days Express. Free shipping on orders $160+.
Basco TE10000 Outer Tie Rod End (Left or Right): Holden Colorado RC, Isuzu D-Max & MU-X
A front outer tie rod end for the Holden Colorado RC, Isuzu D-Max TFR / TFS and Isuzu MU-X, listed by Basco for either side. It's the ball joint that connects the steering rack's tie rod to the steering knuckle, so it directly affects steering feel, tyre wear and your wheel alignment. Doing both sides? The TE10000 pair gets you two in one order.
In stock at our Sunshine Coast QLD warehouse. Order before 1pm and it's dispatched the same day.
At a glance
- Suits: Holden Colorado RC (2008 – 2012), Isuzu D-Max TFR / TFS (2008 – on) and Isuzu MU-X (2016 – on), see fitment
- Position: front outer tie rod end, fits the left or right side
- Pair: two units in one order as the TE10000 pair
- Change it: when there's play, a split or leaking boot, or uneven tyre wear (no fixed interval)
- Brand: Basco, an Australian family-owned parts specialist
Key features
- Wide D-Max coverage: listed for the 3.0L 4JJ1 and 4JJ3, 1.9L RZ4E and 2.2L RZ4F D-Max, including SX, LS-U, Space Cab and Highride models
- Either side: Basco lists one part number for both sides, so one part covers the left or right
- Direct replacement: built as a direct replacement, so no modification is needed (Basco)
- OE specifications: Basco says its steering range is designed to meet OE specifications
Specifications
| Part number | TE10000 |
| Brand | Basco |
| Barcode (EAN) | 9356247158167 |
| Position | Front, outer, left or right |
| Vehicles | Holden Colorado RC, Isuzu D-Max & MU-X |
| Quantity | 1 tie rod end |
Part details as published for Basco TE10000. Compare with your old tie rod end before fitting.
Vehicle fitment
| Model | Engine | Built |
|---|---|---|
| Holden Colorado RC (DX, LX, LT-R, LX-R), single cab & dual cab ute | 3.0L 4JJ1-TCX turbo diesel | 2008 – 2012 |
| Isuzu D-Max TFR / TFS (incl. SX & Space Cab), single, space & dual cab | 3.0L 4JJ1-TCX turbo diesel | 2008 – 2012 |
| Isuzu D-Max TFR / TFS (incl. SX & Space Cab), single, space & dual cab | 3.0L 4JJ1-TCX turbo diesel | 2012 – 2020 |
| Isuzu D-Max TFR / TFS (incl. SX, LS-U & Space Cab), single, space & dual cab | 3.0L 4JJ3-TCX turbo diesel | 2020 – On |
| Isuzu D-Max TFS dual cab & SX Highride TFR cab chassis | 1.9L RZ4E-TC turbo diesel | 2021 – 2025 |
| Isuzu D-Max TFS dual cab & SX Highride TFR single & dual cab | 2.2L RZ4F-TC turbo diesel | 2025 – On |
| Isuzu MU-X LS-M (UCR) 4-door SUV | 1.9L RZ4E-TC turbo diesel | 2016 – 2025 |
| Isuzu MU-X (RJ) 4-door SUV | 3.0L 4JJ3-TCX turbo diesel | 2021 – On |
Basco lists this part for 29 Holden Colorado RC, Isuzu D-Max and MU-X variants. Doesn't suit the Holden Colorado RG or Colorado 7 (2012 – 2020), the 2.5L 4JK1 D-Max, or the Mazda BT-50. Basco doesn't list it for the 3.0L MU-X built 2013 – 2021 either, so check with us before ordering for that model.
Not 100% sure? Send us your rego or VIN and we'll check it for you before you buy.
Part numbers
- Basco TE10000: front outer tie rod end, left or right (this part)
- TE10000 pair: two TE10000 in one order, for both sides
What's in the box
- 1 × Basco TE10000 outer tie rod end
When to replace
Tie rod ends don't have a fixed replacement interval. Have the steering joints checked at every service and replace the tie rod end if there's free play in the ball joint, the rubber boot is split or leaking grease, or the vehicle fails a roadworthy inspection on steering play.
Utes and 4WDs that tow, carry loads or go off-road are hard on steering joints, so if one side is worn, have the other side checked too.
Signs it's worn
- Knocking or clunking from the front when steering or driving over bumps
- Loose or vague steering, or the vehicle wandering on the road
- Uneven or rapid wear on the inside or outside edge of a front tyre
- A split, torn or greasy rubber boot on the tie rod end
- Play you can feel when the wheel is rocked side to side (at 9 and 3 o'clock) with the vehicle raised
Fitting tips
- Before removing the old end, count the turns or measure its position on the tie rod so the new one goes back close to the same toe setting.
- Use a proper ball joint separator. Don't hammer on the threads or the boot.
- Torque the lock nut and the ball stud nut to the figures in your workshop manual, and fit a new split pin if your vehicle uses one.
- Get a professional wheel alignment straight after fitting, because replacing a tie rod end always changes the toe.
Do the full job
Also in stock for the Holden Colorado and Isuzu D-Max (check the fitment on each, as years and models vary):
- Basco BCA1102 + BCA1114 Front Upper Control Arm Pair
- Basco BCA1102 Front Left Upper Control Arm and BCA1114 Front Right Upper Control Arm
- Bendix DB1841-UP4WD Ultra Premium 4WD Front Brake Pads
Why Basco?
Basco Wholesale is an independent, Australian family-owned automotive parts specialist, with warehouses in Victoria, Queensland and New South Wales. Basco is its own house brand of aftermarket parts, with broad vehicle coverage at a fair price.
FAQs
Is this the left or the right side?
Either. Basco lists TE10000 for both the front left and front right outer tie rod end on these vehicles. For both sides, order two or get the TE10000 pair.
Do I need a wheel alignment after fitting?
Yes. Any tie rod end replacement changes the toe setting, so book an alignment straight after to protect your tyres.
Should I replace both sides?
Only if the other side is worn too, but it's worth having it checked while the vehicle is in. If you're doing both, the pair saves $9.95 compared with buying two separately.
Does it fit the Holden Colorado RG?
No. Basco lists it for the earlier Colorado RC (2008 – 2012) only.
Will a non-genuine part void my new-car warranty?
No, not on its own. The ACCC says you can have your car serviced by an independent mechanic using non-genuine parts, as long as the parts are fit for purpose and the work follows the manufacturer's schedule. Keep your receipts and logbook stamps.
Warranty, shipping & returns
- Manufacturer warranty: covered by the Basco manufacturer warranty against manufacturing defects under normal use
- Same-day dispatch: order before 1pm, from our Sunshine Coast QLD warehouse
- Free shipping: on orders over $160
- 30-day returns: unused parts in original packaging can be returned within 30 days of purchase. You pay return shipping unless the item is faulty or was listed incorrectly. Change-of-mind returns attract a 10% restocking fee, as per our refund policy.
Confirm fitment before purchasing. Coo-ee the HOOROO Crew at sales@hoorooautomotiveparts.com.au or tap the AiMate live chat if unsure.