Brakes and wheel bearings work a little differently on an electric car. On a BYD Atto 3 or Dolphin, regenerative braking does much of the slowing down, so the pads often last a long time. But light use brings its own problems, and the car's weight and quietness mean bearing wear tends to show up as noise you can't ignore. This guide covers what to look for, what you can check, and which parts suit the Atto 3 and Dolphin.
Why EV brakes wear differently
When you lift off the accelerator in an Atto 3 or Dolphin, the motor slows the car and recovers energy. The friction brakes only do the work in harder stops and at very low speed. That's good for pad life, but it means the pads and rotors can sit unused for long periods. Common EV brake issues include:
- Corrosion on the rotors, especially on the rear and on cars parked outdoors or near the coast.
- Glazed pads from light, infrequent use, which can reduce bite and cause noise.
- Sticking caliper slide pins, which can cause uneven pad wear between the inner and outer pad.
So even with low pad wear, the brakes still need checking at every service.
Signs your brakes need attention
- A squeal, grinding or scraping noise when braking.
- A pulsing or shudder through the pedal or steering wheel under braking.
- The car pulling to one side when you brake.
- A pedal that feels softer or travels further than usual.
- A brake warning light or message on the screen.
- A rusty, rough or grooved band on the rotor face that you can see through the wheel.
Signs of a worn wheel bearing
- A hum, drone or growl that gets louder with speed, often noticeable from around 50 to 80 km/h.
- A noise that changes when cornering. A bearing usually gets louder as the car's weight leans onto it.
- Play when the wheel is rocked at 12 and 6 o'clock with the weight off it.
- A rough or grinding feel when the wheel is spun by hand.
- An ABS or stability control warning.
Tyre noise is often mistaken for a bearing. Tyre noise usually changes on different road surfaces, while bearing noise tends to stay with you. Uneven or cupped tyre wear can also drone like a bearing.
Simple checks you can do at home
- Look through the wheel at the rotor face. A shiny, even surface is normal. Heavy rust, deep grooves or a lip at the outer edge suggest it needs attention.
- Check the pad thickness through the caliper if you can see it. Compare inner and outer pads if possible, since uneven wear points to a sticking caliper.
- Check the brake fluid level in the reservoir. A dropping level can mean worn pads or a leak.
- Rock and spin test for bearings, with the car safely on stands at the correct lift points.
Never work under a car held up only by a jack. On an EV, only lift at the manufacturer's specified jacking points, so you don't damage the battery pack.
Replace now or keep an eye on it?
- Pads: replace when worn to the minimum thickness in your workshop manual, or if they're glazed, cracked or contaminated. Always replace both sides of an axle together.
- Rotors: machine or replace if they're below minimum thickness, deeply scored or badly corroded. Light surface rust that cleans up after a few firm stops is normal.
- Wheel bearings: replace if there's play, roughness or a related warning light. A faint hum with no play can be monitored until your next service, once tyres are ruled out.
A gentle way to help EV brakes is to do a few firm (not emergency) stops from moderate speed now and then, where it's safe, to keep the rotors clean.
Parts for the BYD Atto 3 and Dolphin
Brake pads (Bendix EV-Hybrid range, designed for EV braking):
- Bendix DB2732-EV Front Brake Pad Set, $138.95: Atto 3 (2021 on), Dolphin (2023 on) and Atto 2, as listed
- Bendix DB2733-EV Rear Brake Pad Set, $129.95: Atto 2, Atto 3, Dolphin, Seal and Sealion 6, as listed. EPB compatible.
Wheel bearing hubs (Atto 3 2021 on and Dolphin 2023 on, as listed; fit either side, sold individually):
- Basco WBH1879 Front Wheel Hub & Bearing Assembly, $199.95
- Basco WBH1880 Rear Wheel Bearing Hub Assembly, $249.95
If you're chasing a clunk rather than a hum, see our BYD Atto 3 clunks, knocks and rattles guide.
DIY difficulty and safety
Front pads: moderate.
- Clean and lubricate the caliper slide pins and pad abutments with a suitable brake grease, keeping it off the friction material.
- Push the pistons back slowly while watching the fluid reservoir.
- Pump the pedal until it's firm before driving, then test at low speed.
Rear pads: moderate to hard. These cars have an electric park brake. Follow the vehicle's EPB service procedure to retract it before pushing the pistons back. Forcing the piston back with the EPB engaged can damage the caliper.
Wheel bearing hubs: moderate. Work on stands, keep the ABS sensor clean and undamaged, and tighten the hub nut and bolts to the torque in your workshop manual. Don't use a rattle gun to final-torque them.
Safety: brakes and wheel bearings are critical safety parts. If you're not completely sure what you're doing, have a qualified mechanic do the job. If the pedal goes soft, the car pulls hard, or you hear grinding, stop driving and have it checked.
FAQ
How long do brake pads last on an Atto 3?
It varies a lot with driving style and how much regen you use. There's no fixed interval, so check them at every service.
Why use EV-specific pads?
EVs brake differently because of regenerative braking. Bendix designed the EV-Hybrid range for those needs, including low noise and anti-corrosion protection.
Do the front and rear pads come as a set?
Each listing is one complete axle set (both sides). Front and rear are separate part numbers.
Will non-genuine parts void my new-car warranty?
Not on their own. The ACCC says you can have your car serviced by an independent mechanic using non-genuine parts, as long as the parts are fit for purpose and the work follows the manufacturer's schedule. Keep your receipts and logbook stamps.
Not sure which part fits your BYD?
Check the fitment table on each product page, read our How to Check Fitment guide, or just ask us. Send your rego or VIN to sales@hoorooautomotiveparts.com.au or call the HOOROO Crew on (07) 5495 1839, and we'll confirm the right part before you order. Spend $160 or more and shipping is free Australia-wide, applied automatically at checkout.
Find it. Fit it. Fair Dinkum™.
The HOOROO Crew
This article is general information only. Always have your vehicle inspected and repaired by a qualified mechanic.