GWM Cannon Ute Clunks & Vibration: Suspension, Mounts & Centre Bearing

Basco DCB1030 drive shaft centre support bearing to suit GWM Cannon Ute 2.0L diesel

The GWM Cannon ute gets used hard: loaded trays, towing, corrugated roads and plenty of highway kilometres. That shows up first in the front suspension and driveline. A knock over bumps, a clunk on take-off or a vibration that comes in at certain speeds usually traces back to one of a handful of parts. This guide covers how to narrow the noise down on a Cannon with the 2.0L turbo diesel, what you can check yourself, and which parts we stock.

Start with when the noise happens

  • Over bumps, potholes or driveway entries: sway bar links or control arm ball joints and bushes.
  • On take-off, or shifting between Drive and Reverse: engine mounts or the rear transmission mount.
  • A vibration or shudder through the floor at certain speeds, or on take-off with a load: the tailshaft centre bearing.
  • When turning: steering components or a ball joint.

Note whether it's front or rear, and left or right, and whether it changes with a load on or a trailer hooked up.

1. Sway bar links: a knock or rattle over bumps

Sway bar links join the front sway bar to the lower control arms. Their small ball joints wear, especially on rough and corrugated roads, causing a light knock or rattle when one wheel hits a bump.

Check: look for split boots. With the ute parked on level ground, grab the link and try to move it. Any clunk or free play in the ball joints means it's worn.

Listed for the GWM Cannon, Cannon NPW and Cannon Alpha (2020 on).

2. Upper and lower control arms: clunks, wandering and tyre wear

The Cannon's front suspension uses an upper and a lower control arm on each side, each carrying a ball joint and rubber bushes. Worn parts can cause:

  • A clunk over bumps or when braking.
  • Wandering or a vague feel at highway speed.
  • Uneven front tyre wear, or an alignment that won't hold.

Check: look for split ball joint boots and cracked or perished bushes. With the front safely raised on stands, rock the wheel at 12 and 6 o'clock. Play here often points to a ball joint (or a wheel bearing). A pry bar used gently near the bushes can show movement that shouldn't be there.

Lower control arms (supplied with the ball joint fitted):

Upper control arms (supplied with the ball joint fitted):

Listed for the Cannon, Cannon NPW and Cannon Premium NPW 2.0L turbo diesel (2020 to 2025). The same arms also suit the Tank 300 and Tank 500 Hybrid.

3. Engine and transmission mounts: a clunk on take-off

Mounts hold the engine and gearbox in the chassis and soak up vibration. Towing and heavy loads work them hard. Signs include a thud on take-off or when shifting between Drive and Reverse, extra vibration at idle, and visible cracking or separation of the rubber.

Check: with the bonnet up, the handbrake on and a helper holding the brake firmly, gently shift between Drive and Reverse and watch the engine from the side (never stand in front of the vehicle). A big lurch or a clunk suggests a worn mount.

4. Tailshaft centre bearing: vibration and rumble

The Cannon has a two-piece rear tailshaft (drive shaft), held in the middle by a centre support bearing in a rubber mount. When the rubber cracks or the bearing wears, you can get:

  • A shudder or vibration through the floor on take-off, especially with a load or when towing.
  • A vibration that comes in at certain speeds.
  • A rumble or growl from under the middle of the ute.
  • A clunk when taking up drive.

Check: with the ute safely supported and in neutral with the wheels chocked, look at the centre bearing rubber for cracks or tears. Try moving the tailshaft up and down near the bearing. Excessive movement or a rough feel when turning the shaft by hand points to wear.

Vibration can also come from wheel balance, a damaged tyre, worn universal joints or a lift that has changed the driveline angles. Rule those out too.

Replace now or keep an eye on it?

  • Replace ball joints, control arms or sway bar links with any noticeable play. These affect steering and stability.
  • Replace a mount or centre bearing with cracked, torn or separated rubber, or a clear clunk on take-off.
  • Monitor a split boot on a joint that's still tight, but plan to replace it soon, as dirt and water get in fast on dirt roads.

Left and right sides have done the same kilometres, so if one side is worn, check the other.

DIY difficulty and safety

  • Sway bar links: easy to moderate. Hold the ball stud with an Allen key or Torx bit while undoing the nut, and tighten with the suspension unloaded (wheels on the ground or both sides supported) so the link isn't preloaded.
  • Control arms: moderate to hard. You'll need a ball joint separator. Final-tighten the bushes with the ute at normal ride height, and get a wheel alignment afterwards.
  • Engine mounts: moderate. Support the engine with a jack and a block of timber while the mount is changed.
  • Centre bearing: moderate. Mark the tailshaft position before removal so it goes back in phase.

Use stands on firm, level ground, never just a jack. Tighten everything to the torque in your workshop manual. Steering and suspension parts are safety-critical. If you're not sure, have a qualified mechanic do the job, and if the steering suddenly feels loose or the ute pulls hard, stop and get it checked.

FAQ

Does the Cannon need an alignment after replacing control arms?
Yes. Any time control arms or steering parts are replaced, get a wheel alignment.

Do the control arms come with ball joints?
Yes. Both the upper and lower arms are supplied with the ball joint and bushes fitted.

Do these suit the Cannon Alpha?
The sway bar links are listed for the Cannon Alpha. The control arms, mounts and centre bearing are listed for the 2.0L diesel Cannon range. For the Alpha, ask us before you order.

I have a lift kit. Will that affect the centre bearing?
It can. Lifts change driveline angles, which can cause vibration and extra wear. Have the angles checked if vibration started after a lift.

Not sure which part fits your Cannon?

Check the fitment table on each product page, read our How to Check Fitment guide, or just ask us. Send your rego or VIN to sales@hoorooautomotiveparts.com.au or call the HOOROO Crew on (07) 5495 1839, and we'll confirm the right part before you order. Due for a service as well? See our GWM Cannon 2.0L diesel service guide. Spend $160 or more and shipping is free Australia-wide, applied automatically at checkout.

Find it. Fit it. Fair Dinkum™.
The HOOROO Crew

This article is general information only. Always have your vehicle inspected and repaired by a qualified mechanic.